L2A Passive Re-Amplifier Kit
- Full Kit
- Step-by-Step Guide
Get started with DIY and build your own professional reamping box with our most popular kit. The L2A is a rugged, sonically transparent re-amplifier that just happens to be a DIY kit. It's also a simple, fun DIY kit that happens to be an excellent piece of studio gear.
Unrivaled feature set
The L2A is the only passive re-amplifier to feature a Neutrik combo XLR/TRS input jack. No need to grab a TRS-to-XLR adapter.
The L2A’s three-way filter switch makes re-amping any source imaginable a breeze. The low-pass filter (LPF) tames high-frequencies, useful for mellowing out guitars and other bright sources, while the high-pass filter (HPF) is perfect for tidying up the low-end and sub-bass frequencies.
- Neutrik COMBO XLR/TRS input jack
- Transformer custom wound in the USA
- Filter stage with Bypass, 1Khz LPF, and 160Hz HPF settings
- Super-durable enclosure made from architectural aluminum
- Circuit board custom designed for beginners
- Metal-film 1% tolerance resistors
- 21-detent stepped potentiometer (volume knob)
- Every nut, bolt, and wire needed to complete the project
The fun part
Designed specifically for DIY beginners, the L2A presents no risk of electrical shock, consists of only a few parts, and can be built in about 30 minutes. Step-by-step instructions are available at diy.re/l2a-manual
Estimated build time: 30 minutes
Make something great
The L2A multiplies the sonic possibilities of your recording setup by letting you plug the output from your computer, mixer, or tape machine into your guitar amps and effects pedals. Suddenly, all of your guitar gear becomes another set of tools for adding excitement, depth, and harmonic saturation to your pre-recorded audio.
|THD+N||<0.05% @ 1K Hz|
|Filter Freqs||160Hz HPF, 1kHz LPF|
What the pros are saying
- Brandon Drury, Recording Review
Really fun and easy project. Works great and high value!
Great Box! Easy to build with a fine, no-nonsense design. Just what I was looking for - thank you!
My previous soldering experience was limited to a few mic cables but this kit and it’s instructions were so easy to follow I completed the build in about 30 minutes. The re-amping box is super effective and works perfectly.
As implied in the title I now have four of these. Two were of the original design and two were from my latest batch which have the updated feature set. It goes without saying that I'm a fan. Can't say that I've found a use for the added filters in the new design but the cutoff frequencies sound both good and useful so I'm sure there will come a time. Also very easy to build. I built two L2As and one L2P while I had COVID so make of that what you will. If you can't smell the solder then it 'aint there, right???
I'd like to one day see a combo unit that combined the L2A with a DI/preamp return path so that I don't have to chew up a mic-pre every time I want to run some pedal shenanigans.
I'd definitely recommend this kit to any fellow audio dweeb. I currently have three of my units running on a mix and they're really bringing the schmutz. Cheers!
This was my first DIY project, though I have some soldering skills from modifying my guitars. Easy build, and it was fun to do. I tested the L2A immediately. Using a recoding of my DI guitar signal from a project in Logic, I re-amped to a preset in my Boss Katana, recording directly to Logic through USB, and also used a Sennheiser e609 to record the speaker. I could then compare the original recording from the Katana, the reamp through the same preset, and the microphone. I could not discern a difference between the 2 Katana tracks, and even the microphone recording showed excellent fidelity to the original (though this latter aspect has nothing to do with the L2A). Tried HPF, LPF and bypass -- for my situation, bypass was the "truest" signal. Perfect! Very impressed.